Furnace Repair in Guelph

Furnaces, like every other device, contain multiple components that can wear out and cause the system to fail over time. The igniter, blower motor, limit switch, flame sensor, and control board are some of the most common furnace parts that can fall short. This is why it’s crucial that homeowners aim to have their heating system professionally serviced by a certified HVAC technician at least once a year. Not only is this going to save you more money on costly repairs over time, but it’s also going to extend the lifespan of your equipment while providing you peace of mind.

If you’ve discovered that your furnace is turned on, but your house is still cold, there might be a few explanations for this. A dirty air filter is a frequent culprit, as it can restrict airflow, making it difficult for your furnace to warm your residence correctly. If that’s the case, you will need to replace or clean the air filter to ensure the airflow is optimal.

Another potential problem is that your thermostat is malfunctioning. If your thermostat isn’t working correctly, it may not be conveying the correct information to your furnace, causing it to run without creating sufficient heat. In some instances, checking the thermostat settings and ensuring that it is set to “heat” mode can resolve the problem. However, if your furnace is in its “heat” setting, you may want to call a repair technician to come to take a look!

Furthermore, if neither of these seems to be the case, the reason could be more technical, such as a problem with the furnace’s ignition system or blower motor. All of these components would be required for a professional HVAC technician to perform a diagnosis and repair.

Water leaking from your furnace can signal bigger issues. It’s critical to address the problem as soon as possible to avoid any damage or safety risks. Possible causes of leaks include:

• Condensation produced by high-efficiency furnaces as part of the heating process. This is usually gathered in a drain pan and emptied away. If the drain line becomes clogged, water may back up and leak from the furnace.
• Clogged or dirty air filter may cause the furnace to overheat and shut down, resulting in water leaking from the unit.
• A cracked heat exchanger is a serious problem that can result in carbon monoxide leaks and other safety hazards. You need to immediately shut off all power to your furnace and exit your home before calling Oosterverld Heating & Air Conditioning and your local gas company to inspect your home.

If you detect water pooling around your furnace while your air conditioner is operating, it could be the result of the following issues.

1. An obstructed drain line: When your air conditioner runs, it produces condensation, which is typically emptied away through a condensate drain line. If the tube gets blocked, the water may back up and overflow, causing it to leak around your furnace.
2. A condensate pump that isn’t working: If your air conditioner is in an area with limited drainage, it might depend on a pump to eliminate water. If the pump fails to function properly, water can build up and leak around the furnace.
3. Frozen evaporator coil: A frozen evaporator coil may cause water to overflow and leak near your furnace. This could be due to low refrigerant levels or constrained airflow.

When your furnace isn’t working correctly and you’re feeling cold air instead of warmth, look out for a few common issues. Start by ensuring that your thermostat is set to “heat” and that the ambient temperature is greater than the present temperature in the room. It’s a straightforward step that’s surprisingly easy to overlook! Next, ensure that your furnace is powered on and turned on. Check the circuit breaker for electric furnaces and check that the gas valve is open and the pilot light is lit for gas furnaces. If none of these things solve the problem, a clogged air filter may be hindering warm air from flowing throughout your rooms.

If your home has a gas furnace and the pilot light isn’t lit or is dirty, your furnace may be unable to produce warm air. To resolve the issue, our technicians can clean or fix the pilot light. In any case, it is critical to address the problem as soon as possible in order to keep your home cozy and warm while preventing further damage to your heating system.

It is not usual for a furnace to make loud noises but when this starts happening in your home, it can be both irritating and frightening. There could be a variety of causes, ranging from something as straightforward as a dirty air filter to more complicated problems like ductwork problems or age-related deterioration. A clogged or dirty air filter may trigger your furnace to work harder than required, leading to noise. Loose or worn-out components, on the other hand, can cause creaking or banging noises. Furthermore, ductwork issues, such as leaks or obstructions, can cause your furnace to generate loud sounds as well.

A dirty or malfunctioning pilot light could be the cause of your furnace’s persistent humming noise. Finally, if your furnace is over 15 years old, it may begin to make more noise due to age-related wear and tear, and you might want to replace it with an updated and better-performing model.

Regardless of the cause, to avoid further damage to your unit, the best thing you can do is reach out to have your furnace inspected and repaired as soon as possible. You can book your appointment with us directly by calling (548) 409-5875!